That means that almost all parts swap between a 302 and a 351. This includes: Heads, cam, lifters, timing chain, timing chain cover, water pump, engine mounts, and all sorts of other stuff. The bellhousing bolt pattern is the same as a 302, so all trannies that bolt to a 302 will bolt to a 351.
What is the difference between a Ford 302 and 351?
On a 302 (or smaller c.i.d.) blocks, the distributor mount is almost flush with the top of the block (where the intake sits). A 351W block is taller. So, the distributor mount is below the block surface where the intake sits. There is also more space between the water passages and the cylinder heads.
How much does an f150 engine swap cost?
Replacing and installing a new engine for a Ford F-150 should, on average, cost between $4000 and $8000. This price can vary dRamatically depending on Your locality, as well as Your access to spare parts.
Will a 351 computer run a 302?
(302 wiring harness/351 engine) You can also just use the 351 computer on a 302. I have tried various computers from 302’s and 351’s and there is very little difference in performance and none in driveability. I am currently running a 351 PCM but ran my stock 302 PCM for over a year.
Will a 302 water pump fit a 351W?
302 and 351W pumps are the same EXCEPT there are 2 different rotations of each and some have different mounting bosses for accessories.
Are 302 and 351W timing covers the same?
Registered. Yes the covers will interchange from 1 block to the other, but you have to match the timing cover to the water pump your using, either standard rotation or reverse rotation.
Is the Ford 302 a good engine?
in stock form the 302 is a reliable and torqie engine that gives excellent gas milage and long life when maintained and used within its limits.
Is 351 Cleveland better than Windsor?
The 351 Cleveland is a member of the 335 series family of Ford small-block engines. Its large ports and oversize canted valves give it more horsepower and allow it to run at a higher rpm than the Windsor. The valve covers have a twisting curve and are attached by eight bolts.
How much does a new truck engine cost?
Unfortunately, replacing an engine often costs more than the vehicle’s worth. On average, you’re looking at $4,000 to $5,000 dollars to replace a 4 cylinder engine. This price is likely to go up with a V6 or V8 engine. And, figures tend to range based on the complexity of a job and the performance of a vehicle.
How long does it take to replace a Ford F150 engine?
Long block is 21.7 hours per “book time”. “Complete” assembly with transfer of parts is 16.7 hours. A shop near you will quote often times based on the job, not the hour.
What’s the difference between a 351 and a 302?
This is needed due to the 351 being much wider than the 302. Due to my 302 being from an 87 and my 351 being from a 90’s F150, I had to jimmy up my 302 bracket to work. The reason that I did that is because of my A/C pump. It bolts up completely differently than the bracket with the engine came with (look at pic below).
Can a 302 engine be swapped for a V8?
If you are swapping from an I6, I think it’s the same thing as the points given up above with the 302. But you will also need to get V8 motor mounts to swap in place of your I6 mounts. There is also allot of re-wiring to do if you choose to use the original wire harness.
What do you need to change a carburetor on a 302?
You will also need the throttle cable bracket attached to the intake manifold and a throttle return spring. Transmission: This is probably the most critical step of the whole process. If you have a manual transmission you have nothing to worry about. However, if you have an AOD automatic you need a TV (throttle valve) cable.
Do you need a new radiator on a 351?
But if you are starting with the big six, it would be a good idea to buy a new radiator, you don’t have to, but in my opinion, a single row radiator is a bad idea on 351. Many people recommend getting a 351 wire harness when you get an engine.
